Chosen Solution My mobile Nokia 1650`s display is not working I can’t operate it and so as torch is also not working plxz fix this problem for sake of nokia I think ur dispaly is damage ,,change it or try to hard reset..or call the engineeer
Chosen Solution I damaged the rubber gasket that goes around the display when fixing the LCD, now it’s back on but I’m missing a piece of it so dust gets in the display. I was wondering if there’s a place where I can get that part so as to replace it correctly or other wise if anyone have an idea of what I can do to fix this without the appropiate part?...
Chosen Solution Look I have a lg stylo 5 and some guy was goofing off at lunchtime and made me loose grip and drop my phone and a black line appeared and it was fine at first and then it decides to screw up like the screen has 100000 finger prints on it I honestly don’t know what to do any help Declared puma this “drop my phone and a black line appeared” is a pretty good indication that you have a broken display....
Chosen Solution The milk steamer leaks when machine is on. See Item on the right: https://d3nevzfk7ii3be.cloudfront.net/ig… It has a tiny washer inside it. I replaced that washer to stop the steamer leaking water and steam at the screw on the join at the washer in the image. What else could be causing the leak? I note one part of this Steamer is brass the other chromed material… heating and expanding at different rates?...
Chosen Solution fell down from 3m hiegt and not on.service center told ic shot really it was the problem no crak is there entire body So from what I can understand the iPhone 6s dropped from 3 metres in height and completely died after that. The issue is caused by something going bad on the logic board. IC meaning a chip or SMD (on board) components which can be one or more has gone faulty....
Chosen Solution Few days ago my laptop suddenly shut off, when I turned it back, it just goes blank, no bios logo. I already tried some solution like removing any hard drive, removing/switching ram, removing battery, connecting external monitor, holding power button for 30s/1m and so on, etc. But still no luck. I’m not sure what’s the problem. Is it cause of a dead gpu? I tried turning on while plugging my external rgb keyboard/mouse, and they didn’t lights up....
Chosen Solution when i turn the fuel on gas well leak out of the air box @baylor we would at least need to know what model and year your bike is and what you have checked. Most common problem is a stuck needle valve that will then disable the float and causing the carb to flood. Check that first, 03 triumph America . hears what’s going on i’m trying to get running witch I did the bike went thew katrina and my buddy got it for parts for he’s bike all he needed was the front tire ....
Chosen Solution turn on defroster to window it wont change it stays in floor or vents . its hot just I don’t have defrost There are 4 doors in your heater box depending on your specific truck. They all have DC motors and plastic driveshafts. The motors are strong enough to break the doors. You can find replacement doors that are steel. Chances are good that you have atleast 2 doors broken....
Chosen Solution I recently had to change my Z3 Compact Display for the second time (broken display). The first time it worked all well but this time the display only showed scrambled graphics. At the boot sequence with the display of the “android” font, it all looked normal but after that, the blue-ish start-sequnece (with the flowing lines etc.) was completely pixelated and scrambled. also the upcoming lockscreen was pixelated and scrambled in the same way....
Chosen Solution Panasonic KX-TGE275S……phones have message check tel line. I can call land line number on cell phone and it will ring, I can answer it. Hang up the receiver and there will be a dial tone and I can make a call out, but in a little while, it will go back to…check tel line and no dial tone…please help Hi @Madeline Baia , What is the make and model number of the landline phone?...
Chosen Solution On a MFC-4420DW I’m attempting to print business cards on Avery stock through the rear, single sheet feed tray. Data transfer from PC is very slow, and when printing begins only the first quarter of image prints and sheet exits printer. Thereafter I get a Paper Jam message. I have followed the “clear paper jam” instructions several times, referred to online instructions, used a letter-sized sheet of glossy photo paper for the “remove paper scraps” function, but printer does not grab the sheet....
Chosen Solution The screen got destroyed on this phone, so I disassembled it to salvage the board. However, I noticed there was. loose contact piece in the shell. I don’t know if it serves an actual electrical purpose though. Take a look at the photos. Thanks. There are small flex cables either on the back side of the case or somewhere else in the phone that connect to those points when the phone is reassembled....
Chosen Solution Hi, my phone fell at a pointy edge on the home button which cause the fingerprint sensor to stop working. After i watched the dissasembly of the galaxy s7 edge i got worried about how the phone would look after taking the screen out and putting it back, i mean can the glow make the screen look exactly like it was never opened ? I know it’s weird but one would think and edge like that is not easy to take out and put back and still look like new Sorry for my english, thank u very much...
Chosen Solution When I Boot Up My Macbook Air 2012 Is Show One Vertical Line Between LCD… What The Solution For This Problem? This is a common issue among Macbook Airs. Reset your PRAM by holding down Command-Option-R-P until you hear a second chime. Already Reset PRAM But Still Same… This Is My Problem.. Hello Any Others Can Help This Problem???
Chosen Solution The display does not light up but itunes detects the ipad. I disconnected the battery and it seemed to work, but after some use it is no longer accessible (itunes, however, detects it). Some advice? Thank you Sounds like maybe the LCD flex cable is coming loose. I’ve actually seen a guy smack the opposite side of an iPad 2 and correct a loose cable. Not sure if the 4 flex would react the same....
Chosen Solution Hello, I just travelled with my iMac 27inch 2015 year model placing it in its original well protected box. The airline promised to send it in Extreme Care Handling luggage tag. I received the box at the belt luggage in the airport and it was fine. No hits or no damages to the box. When I arrived at my place, I switched it on but even though the drive gave me the usual switched on ring, the display remained off....
Chosen Solution i spilled water onto my razer blade pro (2019) and before i realized it,was too late the pc went of,so i dried it out and switched it back on’it runs alright but the screen wont turn on.dont know what else to do,am not really a hardware kinda guy I would not try to restart the device while leave it to dry at least 12 hours. Turn the laptop upside down and see if any water drains out of the machine....
Chosen Solution During start of tv pictures get distorted n images starts flickering and later after 1-2 hrs of viewing it becomes stable..A thin straight line appears at d bottom. You can get a complete set of replacement boards for less than 100 dollars at shopjimmy.com and as long as the screen is not damaged it should fix it they also sell backlight leds
Chosen Solution What do I have to change out to change the oil pressure pump ? Do I have take the entire engine out like on the newer models ? @dragonslayer depends on your engine and how much room you got. I would normally say yes you need to pull it but it looks like it can be done in frame. Anyhow check the write-up on here It is pretty descriptive....
Chosen Solution Hello community, (sorry for mistakes, english is not my first language but i hope you understand) a friend of mine broke the glass of his iPhone 5 and asked me to replace it (only the glass). I watched a few tutorials in the internet where some people show how to separate the glass and the display and put a new glass on the display. I saw that they used a 70% oder 90% alcohol disinfection....
