Posts

Chosen Solution Does the door switch control power to bosch dishwasher model shxm98w75n Hi, Not quite sure bit I think that your model is nearly the same as the Bosch 800 series dishwasher. Here’s an image taken from the service manual for the series that shows how to test the door sensor (switch?) The door switch doesn’t control the power to the dishwasher, it is used to signal the control board that the door is either open or shut so that the dishwashing/drying action etc can either commence/recommence or be stopped by the control board....

Chosen Solution The door keeps opening causing the dryer to quit. How can I keep the door from opening. It is not overloaded, but the clothes on the inside keeps pushing the door slightly open causing the dryer to quit. I also have this problem. pushing the top of my dryer door closes it again so I can start the load once more. it will continue to randomly pop open by itself....

Chosen Solution I proformed the screen replacement from this forum. It went fine, screen works. the only thing that does work is when the phone is closed, there is no audio. Open the phone and the speaker comes on. Did I miss some in the replacement of the screen?? Here’s an idea (not a proven solution) - if you haven’t thrown your ENV3 away by now… On mine, there appears to be some foil tape (or at least silver tape) going from the speaker to the LCD edge....

Chosen Solution Win 7 I ran DLG diagnosis it shows volume name. Quick test Pass Capacity 0.0 GB, extended test Pass Capacity 0.0 GB. anyone that found a solution with similar issue please help. thx If you dont care about data on it, whith the drive plugged in, go into the start menu and type “disk management” and hit enter, there you see all the disks plugged in to your computer, find the one that is the WD passport, right click and then hit format, THIS WILL DELETE ALL DATA, but the hdd should work again....

Chosen Solution Hello. I’ve replaced a battery and now the left fan starts to run at 134%¹ just after turning on mpb. The right fan is starting at very low speed, then it overclocks, so I think it works fine. But there is no any sensible lags on working, cpu temp is fine, only real issue is a fan noise. I’ve tried to reset SMC and NVRAM by several times, nothing has helped....

Chosen Solution Macbook recently got wet. I dried it off and, cleaned off some corrosion from the logic board and let it dry a while longer. Turned it on with no issues aside from some small flickers from screen. Used it that way for a couple days and today the screen went dead for a while. I eventually got some image back but it’s very dim and with constant flickering. Weird part is I can stabilize the flickering a bit by connecting and disconnecting MagSafe charger although it’s a bit more stable if I leave the charger off....

Chosen Solution I have a 2002 - 2.2 grand am . has 17,000 orig. miles . driven weekly. just quit given gas. checked fuses 18-48, still no fuel . cant get pump to work. went bad overnight. live in ALASKA . But have it in warm shop. always under car port.. what should I check from here.???? when pushing in tit in fuel rail gas squirts 10 inchs. no fuel pump noise ....

Chosen Solution I recently got a request to fix an iPad Air, the clients bag was damp and he put his iPad in it and the whole thing basically broke down. 1)ghost touch 2)every time he tried to charge it would turn on turn off if it made it to passcode screen it’d restart 3)home button no longer worked After I opened screen I unplugged flex cables and cleaned them with isopropyl + also I stopped the ghost touch by using electrical tape to secure the flex cable on the digitizer down and fighting the digitizer cable connector to itself by wrapping electrical tape around it Still after those this it the problem I ran into 4)bottom half of screen still no longer responsive 5)home button still unresponsive What the !...

Chosen Solution the hard disc has disappeared from the bios boot menu ASUS say that it could need replacing is this possible and how to do it Hi, According to the specifications for the laptop, it has 32GB eMMC storage. Along with the RAM and the CPU, this is hard mounted on the motherboard and cannot be replaced. The motherboard has to be replaced. This is confirmed by the crucial RAM and SSD checker Is the HDD still being detected by BIOS and that it is just not showing up in the boot menu?...

Chosen Solution Madza 6 2007 cannot put wiper linkage in right park position. Help please Wiper hitting outer side and bottom. Driver side. Hi, Here’s an image showing the distance in millimetres (and inches in brackets) of the wiper blades from the cowl grill end line when the wiper motor is in the park position. The image is from the Body & Accessories section of the 2002-2007 Mazda6 (GG) – repair manual....

Chosen Solution I cannot transfer my Memo files from my Samsung s5 to my pc. I have used all apps when I connect my pc and do a search for .Memo nothing appears 1.Connect the Samsung mobile to a PC. 2.A prompt will appear on your smartphone, ‘Use the Connection For’. You need to tap on ‘Transfer Files’. 3.The name of the device will be visible on the ‘File Explorer’. Enter the device....

Chosen Solution ok when i power on my toshiba satalite it shows the toshiba logo then screan turns black with a pasword comand promped in the uper left hand corner. i got may laptop at a yard sale so i have no password to get to bioss. how can i over ride this password. See if this service can obtain your password for your Toshiba. https://www.ebay.com/itm/Bios-HDD-and-ot…

Chosen Solution Will not boot from Apple Install CD or Diskwarrior CD. Optical drive kick CD out when pressing “C” key. Any suggestions? What install CDs have you been using? The mirror door G4s are a fussy set, will only boot from OSX 10.2.2(approx and above) CDs, not OS9 CDs (even the dual boot models). If the machine is booting, check the machine can see the CD or DVDs ordinarily, if it isn’t the optical drive has probably failed....

Chosen Solution my I7+ was water damage(old one) so I bought a used I7+ (new one)for replace because the new one had a crack on the screen so I change my old one’s screen to the new one. after change screen, touch ID(which is old one’s touch ID ) didn’t work and my new one’s system shows touch ID has issue and will not working then I though it’s because I forgot change touch ID either, so I change touch ID from old one to new one (which is pair with the new one’s CPU) but same thing still happened....

Chosen Solution Changed Chanel, tv went black, picture never came back on. I would assume it is the 5 yr old set but have never had one go bad. Could it be cable co. dvr box? Thanks! @wynglasses at this point anything is possible. Disconnect everything, disconnect the TV and all inputs. Then push and hold the power button for a few minutes. Now plug it in turn the set on....

Chosen Solution I need to know where to buy charge port brackets Just bought a custom 5s shell but need the pieces that go in between the shell and port please help me you mean this piece? http://www.etradesupply.com/apple-iphone… Charge port bracket? What is that? Can u attach some picture?

Chosen Solution Just wondering if my (late 2013 retina macbook pro) is comparable with the new 4 channel SSD that is in the new (early 2015 Macbook pro)? My 2013 has the 2 channel SSD and I want the double speed that the 4 channel offers. Update Sorry, by comparable I meant compatible. I want to know if I can put the 4 channel ssd from the newest MacBook Pro into my late 2013 MacBook Pro retina....

Chosen Solution I’ve done well over 30 systems now and I can tell you the issues come down to two! Bad cleaning! People don’t clean the surfaces properly and/or use the wrong solvents so a film is left. You want to make sure the surfaces are fully clean with none of the old adhesive left. I use a two solvent solution I use goof off to clean the old stuff off where needed and then I use reagent grade isopropyl alcohol 85% or better to pull off the goof off and any other oils using lint free lab wipes....

Chosen Solution I replaced the volume/vibrate/lock flex on my iPhone 5 and once I got it back together the phone is constantly “Searching” for the cellular network. Everything else works on the phone. I also noticed that when I eject the SIM card the phone does not display “No Sim” as it would normally. It is an AT&T iPhone 5. Does anyone have any idea what could have caused this? The cell antenna in the bottom right corner is not compromised and the interconnect cables are attached correctly....

Chosen Solution I have an iphone xs max and it gives me the message that the battery is not original, but this is because I changed the plate and the battery of the old plate does not have the same serial number as the new plate, there will be a way to copy the serial number of the plate and pass it to my original battery replacing the code of the previous plate…?...