Posts

Chosen Solution hi I’m owning a government property laptop and now because of the problem of my laptop hinge it also damaged my laptop antenna wire lately, I fixed my hinge and now my only problem is the wire can anyone help me how to fix m WLAN wire? Hi, Here’s a link to the service manual for the laptop, taken from this webpage. Scroll to p.73 onwards to view the necessary pre-requisite steps and then the procedures for removing / replacing the display panel....

Chosen Solution My wife dropped her Sennheiser RS120 headphones and it came apart. All wires remain connected except the single black wire. I can fix it if I know where it connects. Could I get a wiring diagram so I can fix it. It seems to be OK except that. if you get a magnifying glass you might be able to find the solder point it broke off of.

Chosen Solution Do you offer a service where you will repair a Furby? We don’t offer repairs only the knowledge to help you fix your device. Take a look at this guides: Hasbro Furby 2012 Repair Hi, like Dan has stated, we have basic guides to help guide you to repair your furby(s), and various knowledge to help you identify and fix the problem. Additionally, I am a furby repairest, and if anyone on this site needs further help on fixing their furbys, I will repair it, my email is OliviaRepairs@gmail....

Chosen Solution HP 4440p I inherited the HP from a relative and it quickly became my ‘go to’ pc. After using it in my bedroom I left the HP standing vertically against a nightstand (Lid closed with hinges at the top). The pc was shut down but it was still plugged in with power on to the power unit. During the night i assume I must have knocked a glass containing a sugary drink over....

Chosen Solution does not power up. changed power supply and changed bios battery. result is a blinking led1 on the motherboard. bios battery was at 2.87 volts. do not know how to test power supply. any clues? How dusty was the system when you first opened it up? Did you check the GPU MXM board? A common issue in this series is the GPU board fails and depending on how it fails it can short out causing your single diagnostic LED to blink....

Chosen Solution I have 2 desktops. Pavillion 23 running on 8 & 450-a30 running on 10. They both working fine yesterday . Nothing changed. Connections fine/ Pavillion printing fine. 450 will not print. power of your router for couple of minutes and restart your computers, see if that solve your issue

Chosen Solution Hi there, I’ve had my beats for around 2 years now, yesterday at 7pm I was using them perfectly fine with no problems at all, and then when it came around 11pm it turned on but then shut down after a few seconds, when I put it in charge it shows 3 bars and one flashing so it’s definitely not dead, and occasionally it will turn on but turn off instantly, I have tried the factory reset thing so if anyone is having the same problem or has any solutions please reply...

Chosen Solution My blackberry z10 running on 10.3.2 OS freezes while using sometimes The display fades into a BLACK screen (Doesn’t turn off) After using an autoloader it works nicely for a couple of weeks and the problem appears again Having faith on Blackberry hardware i guess it’s a software problem The phone is made in mexico STL 100-1 I have same problem. STL100-1, made in Mexico. Tried autoloaders, web updates but no solution....

Chosen Solution A family member gave me their old iPhone 6s plus to repair. They dropped it screen first and it broke the digitalizer but not the glass Bought a $50 screen replacement and swapped over the home button. Screen works, home button works and no error for the fingerprint sensor. But when I go to set up touch id it begins to “scan” but will error out within a second saying “keep finger on the home button until asked to lift”....

Chosen Solution How much would it cost to get the front screen replaced to ensure water resistance is not affected. External crack. Hi Michaela Dallat, Sorry to hear about your GoPro. Just get a replacement screen it would be around $17.00 from amazon (http://bit.ly/GoProHero5GR) To actually replace the lens is also quite simple as well. The Process for replacing the protective lens is explained in the following video. (http://bit.ly/GPH5-Lens-Replacement-howt…) If you have any more questions fill free to contact me at dextech87@gmail....

Chosen Solution Hello, When i want to join a multiplayer game, the game will search and join the game. But when it is loading, the game freezes and then takes me back to the xbox lobby. Ive tried allmost anything; powercycle, restored the factory settings with and without the games deleted. Tried other accounts but none will work. Reinstalled it, with and without a the xbox restarting. The game did launch 1 time, but after that it was just freezing again....

Chosen Solution I hve done factory reset, but after setting up getting error data not cleared sync and try again Hold down the button (reboots device after ~8 seconds).Wait until the static logo disappears.Release the button briefly (< 2 seconds), and hold the button down again.Wait until a long vibration is felt. This indicates the factory reset was initiated. Copied from Fitbit solve pin factory clear pls?

Chosen Solution Hi, I’m Harry, my Macbook pro 13" Retina is dead after a spark sound while charging. But if I plug in the charger connector, the green or orange indicator still can be seen. I can see one of the component on the borad had blown off. So my question is, how possible can it be repaired. Please give some suggestion. Thank you. Please the picture below. @harrymaj when dealing with issues like this you must make sure you identify your logic board for us....

Chosen Solution WTW4800XQ4 no matter how many times I try cannot get diagnostic to run. Hi @emunut Search online for W10468340 to find the tech sheet for the washer It details how to get into the diagnostics and the meaning and causes of any error codes that may be displayed. Hopefully this is of some help

Chosen Solution Hello, Someone gave me a Nintendo Switch to fix it. What I’ve already done: After unmounting it I found that the battery was dead (0V) so I ordered and mounted a new one. But it was not working: battery at 2.8V so I suppose not enough to boot. Then I tested the charger: 0V on the out of USB C on the Switch board! So I borrowed one to test if it was really the charger or the connector....

Chosen Solution how do i change the crank shaft position sensor on a 1997 chevy cavilier 2.2 If you are facing the car the crank position sensor will be on the left side of the engine, down low on the crank case. It will be to the left of your oil filter if you are facing the left side of the engine. Crank position sensors are typically easy to unscrew and change....

Chosen Solution I’m missing two screws in the bottom of my Dell Inspiron 5759 and I’m wondering what size of screws fit in it and where to buy them. For $2 USD, try them all. https://www.ebay.com/itm/300pcs-Laptop-S…

Chosen Solution I find it impossible to find 1 or more diagram(s) that clearly show how to make all folds in an iPhone 8 Plus Front Camera and Proximity Sensor Flex Cable in order to perform a replacement. hello Michael, you won’t find it anywhere. Start with the speaker contact, this one has two holes and fits perfectly in its place. Then stick the microphone. The two holes mentioned earlier will perfectly fit the microphone in the right place....

Chosen Solution My Whirlpool dishwasher cycle won’t start. When I turn the power button on, the machine lights up. However when I press the start button to start any cycle, nothing happens. Any ideas what the problem is? Thanks. Hi @mpmitch , What is the model number of the dishwasher? Check that the door latch switch is operating properly. Usually when the door switch isn’t closed the dishwasher won’t start because the control board thinks that the door is open....

Chosen Solution I have an old Xbox 360 Black with a top mounted 120GB HDD. For a while now, the tray hasn’t opened. I used to be able to get by with just leaving a disk in or manually ejecting it, but this problem is different. The only way i’ve gotten the tray to open is by taking apart the console, removing the shell from the Disk Drive, and then re-mounting it inside the console....